Investigation of the Tribological Behavior of Eutectic Al-Si Casting Alloy
Article Sidebar
Main Article Content
Abstract
The effect of roughness of Al-Si alloy on the wear is investigated. Roughness average (Ra) was verified via different polishing, also was using a pin–on-disc of different loads (5, 10, 15) N, different speeds (100, 200, 300) rpm and relative humidity 74%. Different values of Ra are obtained with (3, 5 and 7) μm. Worn surface were characterized using SEM / EDX. The results show that the wear rate of Al-Si eutectic alloys increases with the roughness increase. It was noticed that the specific and wear decreases as roughness decreases. Severe wear was observed at all loads.
Metrics
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
THIS IS AN OPEN ACCESS ARTICLE UNDER THE CC BY LICENSE http://creativecommons.org/licenses/by/4.0/
Plaudit
References
De Buergo MA, Calvo CV, Fort R. The measurement
of surface roughness to determine the suitability of
different methods for stone cleaning. Geophys.
Res.Abs. 2011; 13: 6443-6444. DOI: https://doi.org/10.1021/ol2027398
Caton MJ, Jones JW, Mayer H, Stanzl S, Allison JE.
Demonstration of an endurance limit in 319
aluminum. Journal of Chemical Material Sciences
; 34: 33-40.
Nadu NB, Bi TV. Effect surface roughness on the
hydrodynamic lubrication of one dimensional.
Porous 2007; 15: 278-286. DOI: https://doi.org/10.1080/09076760802571595
Mathia TG, Louis F, Maeder G, Mairey D.
Relationships between surfaces states. Wear 1982;
: 241-250.
Waterhouse RB, Wabuchi AI. The effect of ion
implantation on the fretting. New York 1985:471–
Lee JA. Cast aluminum alloy for high tempruger
applications, NASA-Marshall Space Flight Center, J.
Metals & Materials Society. USA; 2003.
Chowdhury P, Das S, Datta BK. Effect of Ni on the
wear behavior of a zinc-aluminum alloy. Journal
Material Sciences 2002; 3: 2103–2107.
Shivanath R, Sengupta PK, Eyre TS. Wear of
aluminum-silicon alloys. British Foundryman 1977;
: 349-356.
Singla ML, Chawla VI, Study of wear properties of
Al-SiC composites. J. Miner. & Mater. Charac. &
Eng. 2009; 8: 813-819.
Menezes PL, Kishore K, Kailas SV. Influence of
roughness parameters on coefficient of friction under
lubricated conditions. Sadhan 2008; 33: 181–190. DOI: https://doi.org/10.1007/s12046-008-0011-8
Ku KJ, Math TG. Interface roughness effect on
friction map under fretting contact Conditions.
Journal of Tribology International 2010; 43: 1500- DOI: https://doi.org/10.1016/j.triboint.2010.02.010
Kadirgama K, Noor M, Raman MM. Surface
roughness prediction model 6061-T6. Journal
Scientific Research 2009; 25: 250-256.
Karpenko YA, Akay A. Mechanical engineering, a
numerical model of friction between rough surfaces.
Tribology International 2001; 34: 531–545. DOI: https://doi.org/10.1016/S0301-679X(01)00044-5
Takata R. Effects of small-scale texturing on ring
liner friction Victor. Sacramento CA, USA; 2006.